Facebook Profile Twitter Profile Linkedin Profile
GO

Injectable Packing

Injectable Packing materials is done by hand. Tightening the gland nut compresses the material and forces it to conform to any irregular spaces caused by wear.







 
 

Ameri-Pak Injectable Packing that NEVER needs to be replaced !

 
 

American & Metric sized O-RINGS

Injectable Valve & Pump Sealant
Injectable valve Packing Injectable Packing Injectable valve Packing

20 [Order-On-Line]

A blend of exfoliated graphite particles and high-temperature sacrificial lubricants for extreme service applications.

Available In:
10-pack stick cartridges
2.2 lb
11 lb
22 lb
Specifications

25  [Order-On-Line]

A high-performance, chemically resistant product with bearing pellets. Ideal for the toughest applications.

 Available In:

2.2 lb
11 lb
22 lb
Specifications

26  [Order-On-Line]

A non-straining, non-toxic fiber blended with FDA-approved lubricants for clean or food grade applications.

 Available In:
10-pack stick cartridges
2.2 lb
11 lb
22 lb
Specifications


Injectable valve Packing Injectable valve Packing  

27   [Order-On-Line]

A blend of high-performance fibers and chemically resistant lubricants.

 Available In:
10-pack stick cartridges
2.2 lb
11 lb
22 lb
Specifications

29  [Order-On-Line]

A blend of synthetic fibers and non-straining lubricants for general services.

 Available In:
10-pack stick cartridges
2.2 lb
11 lb
22 lb
Specifications

An Easy and Convenient Product to Use

Injectable sealants are easy to install.  
The initial
installation of injectable packing materials is done by hand. Tightening the gland nut compresses the material and forces it to conform to any irregular spaces caused by wear. An anti-extrusion ring composed of suitably sized braided packing material is set at the top and bottom of the stuffing box or packing gland to prevent the injectable packing from being forced out when pressure is applied.

The injection gun

The injection gun utilizes a button-head or flow-through fitting permanently installed on the pump or valve stuffing box.

Since it requires no electricity, the injection gun can be used anywhere to replenish injectable packing easily and conveniently. The all-steel hydraulic gun is completely portable and is very easy to use.

The valve or pump stuffing box fitting allows the injectable packing to be hand-injected into the shaft stuffing box using the injector gun. No downtime is required for the repacking operation since the equipment can continue to run during the repacking operation.

How to use the injection gun

To properly replenish the packing material, the stuffing box fitting must be located. Next, the injection gun is coupled to the fitting.

When the gun is properly coupled to the fitting, the on-off handle on the fitting is turned to the open position and the new sealant in pumped into the fitting until the required amount of sealant is injected.

When the operation is complete, the fitting handle is placed in the off position and the gun is disconnected from the stuffing box fitting. Remember to properly disassemble and return your injection gun to its container where it may be stored until needed again.

Note: Button-head fittings with check ball valve do not required ball valve for on-line repacking.

Customer Review About Injectable Packing

No Reviews for this Product


Call us at: 714-593-9780 Fax: 714-593-9701
     

Our Partners

Mechanial Seal Sale Online

SealSales.com carry high quality market seals to suit all types and Gaskets Materials, like PTFE, Single Spring Seals,O-Rings and etc... more...

Seal and Packing

Usseal.com is our Seal and Packing is a leading manufacturer & distributor of mechanical seals, Grafoil, gasket material, cut gaskets... more...

Mechanical Seals

Mechanicalseals.net are engineered for most pumps, mixer and agitator applications in maintenance. In many cases the designs have been proven to be workhorses over years of use. more...